Validated Stability-Indicating GC-MS Method for Characterization of Forced Degradation Products of Trans-Caffeic Acid and Trans-Ferulic Acid

When dealing with simple phenols such as caffeic acid (CA) and ferulic acid (FA), found in a variety of plants, it is very important to have control over the most important factors that accelerate their degradation reactions. This is the first report in which the stabilities of these two compounds have been systematically tested by exposure to various different factors. Forced degradation studies were performed on pure standards (trans-CA and trans-FA), dissolved in different solvents and exposed to different oxidative, photolytic and thermal stress conditions. Additionally, a rapid, sensitive, and selective stability-indicating gas chromatographic-mass spectrometric method was developed and validated for determination of trans-CA and trans-FA in the presence of their degradation products. Cis-CA and cis-FA were confirmed as the only degradation products in all the experiments performed. All the compounds were perfectly separated by gas chromatography (GC) and identified using mass spectrometry (MS), a method that additionally elucidated their structures. In general, more protic solvents, higher temperatures, UV radiation and longer storage times led to more significant degradation (isomerization) of both trans-isomers. The most progressive isomerization of both compounds (up to 43%) was observed when the polar solutions were exposed to daylight at room temperature for 1 month. The method was validated for linearity, precision as repeatability, limit of detection (LOD) and limit of quantitation (LOQ). The method was confirmed as linear over tested concentration ranges from 1−100 mg L⁻¹ (r²s were above 0.999). The LOD and LOQ for trans-FA were 0.15 mg L⁻¹ and 0.50 mg L⁻¹, respectively. The LOD and LOQ for trans-CA were 0.23 mg L⁻¹ and 0.77 mg L⁻¹, respectively.     

Nonlinear frequency response analysis: a recent review and perspectives

The nonlinear frequency response analysis (NFRA) can be seen as an extension of electrochemical impedance spectroscopy. NFRA gives a full and detailed representation of the system response and can establish a connection between model parameters and the experimentally observed phenomena. In this article, different theoretical NFRA approaches and the most recent application examples are discussed. A simple electrochemical example is used to showcase the benefits and disadvantages of analyzing the system response by using different approaches. In addition, it was shown how to extract experimental harmonic values and analyze them.     

Sensitivity analysis for discrete optimal control problems

We present local sensitivity analysis for discrete optimal control problems with varying endpoints in the case when the customary regularity of boundary conditions can be violated. We study the behavior of the optimal solutions subject to parametric perturbations of the problem.     

Three Electrons in a Two-Dimensional Parabolic Trap: The Relative Motion Solution

In agreement with the Kohn theorem the relative motion (rel) of three electrons in a two-dimensional parabolic trap separates from the centre-of-mass (CM) motion. By introducing new coordinates the Hamiltonian for relative motion in the approximation of non-interacting electrons can be taken to the normal form. The eigenstates of the normalized Hamiltonian are products of the Fock-Darwin states for normal modes. The energy levels for relative motion are obtained by diagonalizing the exact Hamiltonian in the eigenbasis for the non-interacting case. In this basis the interaction matrix elements can be obtained in the analytical form. Since the rank of the Hamiltonian matrix is significantly reduced, the calculations are faster and more accurate than those for the full (CM + rel) motion. This advantage is especially important for the calculations of excited states and the analysis of energy spectra.     

Comparison of two models for managing reliability growth during product design

Relying on reliability growth testing to improve system designis neither usually effective nor efficient. Instead it is importantto design in reliability. This requires models to estimate reliabilitygrowth in the design that can be used to assess whether goalreliability will be achieved within the target timescale forthe design process. Many models have been developed for analysisof reliability growth on test, but there has been much lessattention given to reliability growth in design. This paperdescribes and compares two models: one motivated by the practicalengineering process; the other by extending the reasoning ofstatistical reliability growth modelling. Both models are referencedin the recently revised edition of international standard IEC61164. However, there has been no reported evaluation of theirproperties. Therefore, this paper explores the commonalitiesand differences between these models through an assessment oftheir logic and their application to an industrial example.Recommendations are given for the use of reliability growthmodels to aid management of the design process and to informproduct development.